Honeywell Security Intrusion and Communications, ADEMCO, AlarmNet, IntelliSense, Apex, FBII, electronic security systems, burglary alarms and fire alarms for. Installation manual for the Honeywell wireless three-zone sensor. For help installing your , call The Honeywell is a wireless three zone sensor. Unlike other Honeywell wireless window and door sensors, the does not have an internal reed switch.

Author: Vijora Voodoolmaran
Country: Armenia
Language: English (Spanish)
Genre: Marketing
Published (Last): 26 June 2004
Pages: 479
PDF File Size: 9.2 Mb
ePub File Size: 4.16 Mb
ISBN: 991-7-55254-450-7
Downloads: 45924
Price: Free* [*Free Regsitration Required]
Uploader: Fegore

When a satisfactory location is found, remove the battery and proceed with installation. The has its own unique identification codes permanently assigned during manufacture. Got it, continue to print. For this application, the alignment guide strip along one edge of the plate serves no function and may be broken away, if desired. Although two holes are provided in the unit that would permit mounting directly to a surface holes “A” in Diagram 2it is recommended that the mounting plate be used, as described below, for ease in removing the unit for servicing should it become necessary.

The Primary Loop has several DIP switch selectable options that determine its connection requirements, response, and transmission characteristics see DIP switch setting table on next page.

Honeywell ADEMCO 3 Point Wireless Transmiter | eBay

Comments to this Manuals Your Name. If a contact loop is not to be used, no connection is needed across its terminals.


Enter text from picture: Attach the case back to the mounting plate by sliding the keyhole slots in the case back down. The two Auxiliary Loops are closed-circuit, with a nominal response time of mSec.

Complain wrong Brand wrong Model non readable. Don’t show me this message again.

Wiring Connections; Specifications – Honeywell ADEMCO Installation And Setup Manual [Page 2]

Risk of fire, explosion, and burns. With the battery still not inserted, connect the loop wiring to the unit’s terminals see Diagram 2. Disengage the supplied mounting plate from the unit by inserting the blade of a small.

Recommendations must be included for a adsmco. For UL installations with fire zones, the position 4 ON setting must not be used.

Honeywell ADEMCO 5817 3 Point Wireless Transmiter

Remove the transmitter’s cover if not already off as described in Mounting Step 1. Observe correct polarity and insert the battery provided into the battery holder see.

The installer should assume the responsibility of developing and offering a regular ademck. Add to my manuals Add. Install the mounting plate, with its case holding posts pointing up in this examplein the. Dispose of used batteries promptly. To replace the cover, engage the hooks along one edge and snap shut. Do not recharge, disassemble, heat above. The description that follows assumes that the unit will be mounted as shown in the diagrams. Regular maintenance and adekco at least annually by the installer and frequent testing by.


Surface wiring should enter via the thin “breakout” area provided in. Seller shall have no obligation under this Limited Warranty or otherwise if the product s is altered or improperly repaired or serviced by anyone other than Honeywell factory service. Customer understands that a properly installed and maintained alarm system may only reduce the risk of a burglary, robbery, fireor other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result.

The should be treated as “RF” i.

To print the manual completely, please, download it. It is not necessary to program the transmitter IDs during installation. Except in the case of the position 4 ON setting, the Auxiliary loops are not affected by. Seller’s obligation shall be limited to repairing or replacing, at its option, free of 581 for materials or labor, any product s which is proved not in compliance with Seller’s specifications or proves defective in materials or workmanship under normal use and service.

The locking tab will click as the case back locks in place. By pressing ‘print’ button you will print only current page.

Author: admin