AOR AR5000 MANUAL PDF

This page lists links, related pages and software support for the AOR AR receiver. The technical specifications can be viewed here (copied from Universal . The AR has been designed & manufactured by AOR Japan who are page 68 and 69 of the AR instruction manual in order to register the new filter. AR Operating Manual addendum (84kB) · AR+3 Operating Manual addendum (kB) · ARA / ARA+3 Operating Manual addendum.

Author: Majind Mikajora
Country: Belarus
Language: English (Spanish)
Genre: Love
Published (Last): 24 October 2010
Pages: 289
PDF File Size: 18.69 Mb
ePub File Size: 10.75 Mb
ISBN: 619-5-41356-549-5
Downloads: 17264
Price: Free* [*Free Regsitration Required]
Uploader: Mizilkree

Scanning A Memory Bank Note: Ar50000 aerials may be connected using the optional aerial switching unit AS with switching data being fed from a rear panel accessory socket ACC 2. Using a match stick or similar tool, press and release the reset switch with the unit switched on, and powered in a normal manner. Page 11 MODE select menu using a short cut Since writing the above Octobera third type of cable has been supplied. Page 74 Short wave desktop loop aerials have the advantage of called the ABF To observe these birdies set the squelch control to threshold point, disconnect the external antenna, set to NFM and rotate the main tuning knob.

No alteration in receiver performance is noticed. The last entered frequency in VFO may be lost. There is much confusion over the issue of 8. A revision to operation firmware appeared after about one year, the serial numbers changed to 07xxxx six digit numbers starting zero seven with four digits following. The operating manual does not xor deal with step-adjust during program search, so ignore it at this time.

  1N3712 DATASHEET PDF

Trouble Shooting – Microprocessor Reset The reset switch is located at reset the top of the slot about 10mm behind the front panel. To enable the fastest search rates, display mode but the input of text is not mandatory.

AOR AR Operating Manual

Operation of some of these other functions would be more difficult and jumpy if the encoder response speed was very different. Remove the six screws holding this board and hinge it over the front panel, removing necessary connectors – protect the top of the front panel with a soft xr5000.

It is taken from the unused output of the secondary winding of I. If you decide to lubricate the bearing, use a light oil that will not stiffen with time.

In particular it has been reported that the ‘clicks’ are most noticeable when the AR is tuned across the following frequency boundaries: At majual, on well used older sets, it may be worth removing the bearing completely. In this condition the AR will select different ways. Re-fit ar55000 encoder and test your work. To send more than one, MSComm1. It is possible to add text at present at this time.

In practice however you will probably not notice any change and we recommend that they are left as standard.

Page 21 VFO mode. Alternatively press to abort entry and return Step-adjust to VFO mode. Don’t have an account?

The AR aorr switch-on automatically once per day presuming the receiver had been switched off on a daily basis at the Program Search – Delay Note: Approximate output levels to be expected directly from the IC are with a large signal input and 1kHz tone: The meter response throughout the VHF region is reasonably flat and will give readings of similar level.

  JASSER AUDA PDF

The process will halt when a busy frequency is located, at default the delay is two seconds after the The DELAY parameter affects the time the AR will transmission clears then resume searching again when remain on an active frequency in VFO search once the the frequency is clear. Reassembly is a reverse of the above.

Two thousand memories in 20 banks of are featured. Only add a small amount of oil as the main dial brake operation may be compromised if too much is added.

AOR AR5000 Operating Manual

It is more intended as a ‘rotary switch’ used for several other functions in addition to frequency tuning. All points are clearly labelled on the board and there is no need to remove the board.

The circuit is shown below After fitting the filter, refer to page 68 and 69 of the AR instruction manual in order to register the new filter. Controls for operation are located on the front of the Display of operational information is provided via a high cabinet with connections to the rear. Mamual following commands are required to do this: The large front panel is very comfortable to use. Figure SIX for the numeric input of frequencies, bank, automatically after a prescribed time period of 1 to channel numbers etc.

The AR will continue to search but will add

Author: admin