ASTM A109 PDF

ASTM A/AM: Standard Specification for Steel, Strip, Carbon ( Maximum Percent), Cold-Rolled. ASTM A Standard Specification for Steel, Strip, Carbon ( Maximum Percent), Cold-Rolled1_幼儿读物_幼儿教育_教育专区。. ASTM A Carbon Steel, Tempers 4 or 5, Composition Spec. Categories: Metal; Ferrous Metal; ASTM Steel. Material Notes: Cold Rolled Strip. Vendors: No.

Author: Dubar Tojakazahn
Country: South Africa
Language: English (Spanish)
Genre: Education
Published (Last): 24 June 2009
Pages: 387
PDF File Size: 1.70 Mb
ePub File Size: 2.1 Mb
ISBN: 805-2-55678-662-8
Downloads: 84906
Price: Free* [*Free Regsitration Required]
Uploader: Tojanris

ASTM A Carbon Steel, Tempers 4 or 5, Composition Spec

Please contact us at webmaster matweb. C A soft ductile cold-rolled strip intended for deep drawing where stretcher strains or uting are permissible. Over 12 to Over Please read our License Awtm regarding materials data and our Privacy Policy. C The analysis shall be reported. NOTE 3—The industry denition as invokved here is: For Specied Width, in.

When the above aging characteristics are undesirable, special killed generally aluminum killed steel is used. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn. An above average surface with better brightness and lower Ra values, sometimes referred to as No.

The use of a lighter load results in a loss of sensitivity, while a heavier load leads to a loss in accuracy. This standard has been approved for use by agencies of the Department of Defense. We also ask that you refer to MatWeb’s terms of use regarding this aastm. Note 2—Camber tolerances as shown in the table are for any mm length.

  EBOOKWISE 1150 PDF

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

However, such products are technically classied as cold rolled sheet. MatWeb is intended for personal, non-commercial use. The contents, results, and technical data from this site may not be reproduced either electronically, photographically or substantively without permission from MatWeb, LLC.

Users requiring more precise data for scientific or engineering calculations can click on the property value to see the original value as well as raw conversions to equivalent units. For strip length asttm mm, camber tolerance shall be subject to negotiation. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

X109 is common practice to make the Rockwell hardness test at a point midway between the side edges on a single thickness only. The contents, results, and technical data from this site may not be reproduced either electronically, photographically or substantively without permission from MatWeb, LLC.

  CANCIONERO CATOLICO ACORDES PDF

W109 values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. All tests and inspection except product analysis shall be made at the place of manufacture unless otherwise agreed.

ASTM A109 Grade 1 hard

When requested, heat analysis shall be reported to purchaser or his representative. Product analysis is appropriate on these types of steel only when misapplication is apparent or for copper when copper steel is specied. Current edition approved Sept.

When killed steel is specied and aluminum is the deoxidizing element, the minimum is 0. A medium soft cold-rolled strip xstm for limited bending, shallow drawing and stamping.

Packaging and Package Marking This table is presented as a matter of general information. Conformance to SI tolerances is mandatory when the “M” specication is used. Aging may cause slightly higher values when tested at a later date. This analysis a1099 conform to the requirements shown in Table 1. This edge is produced when the width tolerance and edge condition are not as exacting as for No.

Link to Active This link will always route to the current Active version of the standard.

Author: admin