ASTM D6484 PDF

ASTM D is a test method used to study the compressive properties of a composite laminate that has a hole cut into it. The GD fixture meets the requirements of ASTM D for open-hole compressive strength testing of fiber-reinforced polymer-matrix composite. The ASTM D / DM fixture is used to perform open-hole compressive tests on multi-directional polymer matrix composite laminates reinforced with high .

Author: Kazragore Kimuro
Country: Cyprus
Language: English (Spanish)
Genre: Photos
Published (Last): 13 April 2009
Pages: 265
PDF File Size: 11.32 Mb
ePub File Size: 10.92 Mb
ISBN: 504-2-56373-491-3
Downloads: 41914
Price: Free* [*Free Regsitration Required]
Uploader: Kagagore

Ma8 chining tolerances and surface?

ASTM D Compression Fixture for Fiber Composite Laminates| GD

Holes should be drilled undersized and reamed to? Damage caused by hole preparation will affect strength results. In such cases, the mechanical test environment may need to be modi?

Tighten the four bolts just enough to hold the specimen in place during? A number in parentheses indicates the year of last reapproval. Wyoming Test Fixtures Inc. Chamber conditions shall be monitored either on an automated continuous basis or on a manual basis at regular intervals. Additionally, a micrometer or gage capable of determining the hole diameter to ? ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

End-loaded tests were performed with no additional?

ASTM D Testing Fixture

The threading of the support plate is optional. This laminate has relatively high stiffness wstm high notch sensitivity and was selected to produce high failure forces in order to evaluate the two loading methods using test laminate parameters representing the upper capability of the test method.

  IFM SR0150 PDF

The test laminate con?

The range of acceptable test laminates and thicknesses are described in 8. Two acceptable test procedures are provided.

However, since the notch dominates the strength, consistent preparation of the hole, without damage to the laminate, is important to meaningful results.

The 6d484 stated in each system are not exact equivalents; therefore, each system must be used independently of the other. The void content equations of Test Method D are applicable to both Test Method D and the matrix digestion procedures.

ASTM D6484 Open-Hole Compression (OHC) Testing of CFRP

Retests shall be performed for any specimen on which values are not astk. If the platens are not sufficiently hardened, adtm simply to protect the platen surfaces, a hardened plate with parallel surfaces can be inserted between each end of the?

Record and report the specimen cutting and hole preparation methods. Work Item s – proposed revisions of this standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Threaded support plate used with bolt-only installation.

For non-ambient environmental conditions, the recommended? If the fixture is loaded between flat platens, some type f6484 lateral constraint should be provided so that the fixture does not slip out from between the platens while being compression loaded, as a safety precaution. One of the reference coordinate system axes normally the Cartesian x-axis is designated the reference axis, assigned a position, and the ply principal axis of each ply in the laminate is referenced relative to the reference axis to de?

  DECRETO 2685 DEL ESTATUTO ADUANERO PDF

ASTM D6484 Testing Fixture

Measure the hole diameter, D, distance from hole edge to closest coupon side, f, and distance from the hole edge to coupon end, g. This may result in non-conservative data. Report both the nominal where: For typical specimen geometries, an instrument with an accuracy of 3? In Procedure B, the? If the specimen is end-loaded, it may be desirable to provide some additional clamping force at the ends of the specimen, to minimize end-brooming. Sampling and Test Specimens 8.

Sources of variation in this lateral pressure include?

If the gap is too large, shim between the support plate and the d648 grip, holding the shim stock on the support plate with tape. The portion of the force initially transferred into the support?

Author: admin