ASTM F594 PDF

or visit us at ASTM F Scope – This specification covers the chemical and mechanical requirements for stainless steel. ASTM F specification covers chemical and mechanical requirements for stainless steel nuts in diameters ranging from 1/4″ to /2″. ASTM F covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, four martensitic and one precipitation hardening. BoltPort.

Author: Najas Dailmaran
Country: Brazil
Language: English (Spanish)
Genre: Politics
Published (Last): 13 December 2014
Pages: 41
PDF File Size: 3.68 Mb
ePub File Size: 19.47 Mb
ISBN: 476-1-32553-817-7
Downloads: 96419
Price: Free* [*Free Regsitration Required]
Uploader: Got

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Historical Version s – view previous versions of standard. This specification covers the requirements for stainless steel nuts in specified size, inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.

ASTM F594 Specification

A Minimum values except where shown as maximum or as a range. F When approved by the purchaser, alloys or Se may be furnished. Unless otherwise specified, all bolts, hex cap screws, and studs used with these nuts shall conform to the requirements of Specification F and shall be of the same alloy group.

AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming.

CW – Headed and rolled from annealed stock t594 acquiring a degree of cold work. A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer B See section 4. The finished fasteners shall meet the applicable mechanical properties.

  MACDONELL VEDIC GRAMMAR PDF

ASTM f Nuts|ASTM F Specification | Nuts Fasteners| Get a Live Quote Now for ASTM f Nuts

Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening: Condition CW – When Condition CW is specified, the ferritic alloys shall be annealed in accordance to above condition A for ferritic alloys, generally by the raw material manufacturer and then cold worked to develop the specified properties.

E When approved by the purchaser, alloy F may be furnished. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

A – Machined from annealed or solution annealed stock thus retaining the properties of the original material; or hot formed and solution annealed.

The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Condition CW – When Condition CW is specified, the austenitic alloys shall be annealed in accordance with Condition A, generally by the raw material manufacturer and thenc old worked to develop the specified properties. Condition AF – When Condition AF is specified, the ferritic alloys shall be annealed in accordance to same above condition A Ferritic Alloys after all cold working including heading and threading has been completed.

It is informational only and not an official part of the standard; the full text of the standard ashm must be referred to for its use and application.

  FORMATO TEST WARTEGG 8 CAMPOS PDF

Free Technical Information

Chemical tests; mechanical tests; and corrosion resistance shall be performed to conform with the specified requirements. Link to Active This link will always route to the current Active version of the standard. B legend of conditions: D Yield strength is the stress at which an offset of 0.

SH – Machined from strain hardened stock or cold worked to develop the specific properties. This abstract is a brief summary of the referenced standard. Condition AF – When Condition AF is specified, the austenitic alloys shall be annealed in accordance to Condition A after all cold working including heading and threading has been completed.

A Tensile stress areas are computed using the following formula: AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming CW – Headed and rolled from annealed stock thus acquiring a degree of cold work. C The yield and tensile strength values for full size products shall be computed by dividing the yield and maximum tensile load value by the stress area for the product size and thread sizes determined in accordance with Test Methods F ASTM F covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, four martensitic and one precipitation hardening.

Author: admin