ATTANSIC ATTP1 PDF

, 13, ATTANSIC, -. Kring Electronics Co., Ltd. , -, Attansic, sop8. 63, 0, ATTANSIC, -. Rantle East Electronic. , -, ATTANSIC, SOP. 年12月11日 ATTP1_ – Technology Corporation ATTP1 Over Temperature Please contact Attansic Technology Corp. for the latest documents. Attansic. ATTP1. Tel:. MFG:. ATTANSIC. Picture. D/C:. 09+. QTY:. Packaging:. SOP8L. Package:. Note:. 原装正品. Support. No“ATTP1”Picture.

Author: Taucage Merisar
Country: Chad
Language: English (Spanish)
Genre: Medical
Published (Last): 27 September 2016
Pages: 374
PDF File Size: 5.39 Mb
ePub File Size: 20.78 Mb
ISBN: 697-4-72930-541-3
Downloads: 56267
Price: Free* [*Free Regsitration Required]
Uploader: Mooguzilkree

This means that your poor CPU is going to blow its brains out just as soon as it loses proper cooling for any reason.

I use to type in short sentence. As a result, when you tie the Temp 3 input to the thermal diode while the Attansic chip is hooked up, it causes the Attansic xttansic to think that the CPU has exceeded safe temp limits. Webb City, Mo Posts: Also make sure that you don’t accidentally bridge any of the adjacent pins with solder while you are trying to lift this pin. Apply a dollop of gel type super glue or some other fastening agent to each of your jumpers to near pin 97 and pin to keep them from flexing too much and breaking the pins off the chip.

Attansic ATTP1 datasheet & applicatoin notes – Datasheet Archive

You don’t need to move the jumper though. You will find that it is easiest to thread the jumper on the diagonal under the CPU socket between the pins. Find pin of the Winbond chip.

Find pin 97 of the Winbond chip. Run a jumper from pin 61 of the Winbond chip to pin That is one of the reasons Attanxic did it the way Attansoc did, so that you could undo it if necessary. The original mod involved disabling the Attansic chip protection because simply hooking the thermal diode from the CPU to the Winbond chip would result in the system not atfansic up, and the familiar two-tone “You’ve got something really mucked up” siren.

  GERD GIGERENZER BAUCHENTSCHEIDUNGEN PDF

You’ll find that trying to solder the wires to the broken pins, while not impossible, is exceedingly difficult. The possibilities are endless! I’ve been looking for developer’s docs for the NF2 chipset and haven’t been able to find any. I’ve personally verified this a few times myself, so I know it works.

ATTP1 Attansic CPU thermal protection controller chip SOP8

If you have previously modded your mobo to read the thermal diode, you MAY find that your temps are degrees higher than they used to be. Make sure you leave just a dollop of solder on the end of the jumper wire when attabsic tin it or you’ll never get it to solder properly but don’t leave too much, or you’ll bridge the pins.

Well, I’ve solved that problem. As for the atgansic, does it have a thermal diode? Soldering on these quad flat packs is a real PITA! I’ve got pretty steady hands and it took me three tries to get the jumper soldered correctly without bridging solder to the other pins.

The wire will need to be about athansic cm 3″ long.

ATTP1 – – IC Chips – Kynix Semiconductor

It is the 4th pin from the top right corner of the chip going down the right side of the chip, when viewed as described above.

It is the pin at the very top left corner of the Winbond chip on the top, when viewed as described above. It is more likely that you will mess it up such that the OTP function trips prematurely and you aren’t able to power on the computer at all. You will need to carefully lift this pin from the solder pad.

  ELASTIX AL RITMO DE MERENGUE PDF

Our members offer you their FAQs! This is the 5vsb input. When the PSU is shutdown or in standby, attxnsic rail is dead, and all of the items connected to the monitor inputs are no longer in a high impedance state. If you muck this up and turn your board into a doorstop, don’t come crying to me.

Anything else is nearly impossible. Solder to pin 61 first, then pin Tie the analog voltage supply for the Winbond chip to the 5vsb rail instead of the 5v rail. This is the top right pin on the Attansic chip, when viewed with the mobo oriented as described above. I will have no sympathy. As for the other, yes you should solder pin 4 of the Attansic back artansic to the mobo.

However, because of the way the mod is done, the odds of messing it up in such a way that you dissable the OTP function are pretty low. This connects to channel two of the Winbond chip, which means you can now use channel two on pin for something else. Where’s the thermal diode? BB code is On. Find pin 61 of the Winbond chip.

So what is the solution? A fine tip aytp1 iron is definitely a must.

Author: admin