BENINCA BRAIN 24 PDF

Beninca Brain 24 Manual. Instruction Manual for Beninca Brain 24 Control Panel. Copy to Email · Send to Mobile. Print. Download · Buy Product. Name. 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 8k2 Command central for 1/2 24Vdc motor, for single or sliding doors: BRAINY Beninca Brain 24 – EasyGates Manuals & Guides. L Rev. 02/06/02 CENTRALE DI COMANDO CONTROL UNIT STEUEREINHEIT CENTRALE DE.

Author: Kizil Tojataur
Country: Barbados
Language: English (Spanish)
Genre: Health and Food
Published (Last): 10 July 2013
Pages: 217
PDF File Size: 19.63 Mb
ePub File Size: 4.30 Mb
ISBN: 727-6-65257-636-7
Downloads: 46914
Price: Free* [*Free Regsitration Required]
Uploader: Shakagul

Add to my manuals Add. The performance of the output vrain preset by 2ch parameter, see previous parameter. The amperometric sensor benninca is interpreted by the control unit as limit switch.

The operating time is adjusted at normal speed during motor 1 opening and closing phases. OFF mloc Selects the type of electric lock used.

Other special functions follow the parameters and logic menus and may vary depending on the type of control unit or the software release.

Beninca BRAINY24 24Vdc Control panel for 1 or 2 motors REPLACES BRAIN24

Contact controlled by 2nd radio channel of the receiver. Parameters, Logic and Special Functions The tables below describe the individual functions available in the control unit. Got it, continue to print. The transmitter codes are bdninca erased from the receiver. OFF Blc The lock function is enabled or disabled. The amperometric sensor activation is interpreted by the control unit as obstacle present in the gate movement area.

  INTIMOS ENEMIGOS OLGA SALAR DESCARGAR PDF

For example, with the leaves completely closed the display is as follows: CLr By selecting this function, the receiver awaits Push for a transmitter code to be erased from memory.

Similarly to the safety edge activation, the control signal is sent to stop and reverse movement for approx. Receiver enabled for rolling-code and programmable code transmitters self-learning and Dip Switch. If the code is not valid, the wording Err is displayed. OFF serL Service light function is enabled or disabled on output Blinking is activated 3s before the motor starts. The speed of the motor during braking is determined by the Brajn parameter value.

In the event of failure it switches on according to the following scheme. Before each opening manoeuvre the power supply is interrupted for the time set by the parameter TLOC. Comments to this Manuals Your Name.

Beninca Brain 24V PCB Board and Casing

If the battery charger board CB. The parameters menu allows you to assign a numerical value to a function, in the same way as a regulating trimmer.

Brrain 2ch logic Off: The preset time should therefore be lower than the real stroke of the operator. Don’t show me this message again. After waiting 60s the control unit quits programming mode and switches off the display.

SCA contact, open gate indicator. The step-by-step impulse or transmitter impulse has no effect during the opening phase. Page of 9 Go. RTR Completely erase the receiver memory.

The control signal is sent to stop the movement. The value is expressed in percentage with respect to speed during normal operation. With the gate open or in the opening phase the intervention of the photocell causes automatic closing after 3 s.

  FVS124G MANUAL PDF

OFF Sld Enables or disables slowing. Limit switches not provided. Other special functions follow the parameters and logic menus and may vary depending on the type of control unit or the software release. The logic menu allows you to activate or deactivate a function, in the same way as setting a dip-switch.

For example, with a 20s stroke, preset 17s to start the braking phase, 3s in advance with respect to end of movement. OFFas the end of operation is determined 11 only by the triggering of the limit switch or by the amperometric sensor.

BENINCA BRAIN 24 OPERATING INSTRUCTIONS MANUAL Pdf Download.

The output has the function of 2nd radio channel: Adjustment of braking With braking enabled SLD logic: If the code is not valid or is not in memory, the wording Err is displayed.

To use this function, close the limit switch contacts with jumpers.

After the activation of closure limit switches the control unit delays the stop by approx. Returns the control unit to the default values.

If buffer batteries are used, connect the CB. Radio receiver enabled only for rolling-code transmitters. By pressing ‘print’ button you will print only current page. Electric lock with latch, normally not fed.

Active only with TCA: With 2ch logic On:

Author: admin