(1) for units intended to be used in elements subject to structural requirements. (2 ) for units intended to be used in elements subject to fire requirements. This Guide to BS EN has been prepared to assist anyone involved in the design, specification and ordering of aggregate concrete blocks to understand. Buy BS EN SPECIFICATION FOR MASONRY UNITS – PART 3: AGGREGATE CONCRETE MASONRY UNITS (DENSE AND.
|Published (Last):||19 September 2018|
|PDF File Size:||1.35 Mb|
|ePub File Size:||18.35 Mb|
|Price:||Free* [*Free Regsitration Required]|
Free to use BIM project management tool provides step-by-step help to define, manage and validate responsibility for information development and delivery at each stage of the asset life cycle in level 2 BIM projects. The net dry density is rarely likely to be a necessity in practice. Some of these test methods are familiar but others are new. Configuration also covers flatness requirements for the faces of facing quality units only, and flatness requirements for the bed surfaces of units to be used with thin 77-13 mortar in D4 tolerance category.
Inthe Concrete Block Association replaced the Aggregate Concrete Block Association as the trade body for manufacturers of aggregate concrete building block in Great Britain. The Amber document status indicator indicates that some caution is needed when using this document – it is either: The tabulated value or a measured value is of no practical use as bond strength in practice will be dependent on a number of factors outside the control of the producer and a value could not be guaranteed as being universally applicable, but only for a set of specific conditions, which would be difficult to replicate on site.
Document Status Indicators The Green document status indicator indicates that the document is: Aggregate concrete masonry units dense and light-weight aggregates. Learn more about the cookies we use and how to change your settings. BS EN puts lower limits on: This document Older versions. Aggregate concrete masonry units dense and light-weight aggregates Status: A category I unit would be approximately equivalent to special category as defined in BS and would require third party certification vs monitoring of the production control system.
These are slightly higher than strengths determined to BS Aggregate concrete masonry units Dense and 7711-3 aggregates is a new harmonized Standard for aggregate concrete bricks and blocks. The check is to be seen as a qualification test and need only be repeated in the case of principal changes to the design dimensions of units.
Aggregate concrete masonry units Dense and light-weight aggregates AMD No longer current but cited in Building Regulations guidance. Click to learn more.
The test method for dimensions is BS EN This is a harmonized European Standard and fully takes into account the requirements of the European Commission mandate M, Masonry and related products.
Determines the characteristics and performance rn of aggregate concrete masonry units made from dense and een aggregates or a combination of both. Additionally includes concrete masonry units of an overall non rectangular parallelepiped shape, specially shaped and accessory units. A third party to monitor the factory production control system is not essential.
Their committees work with the manufacturing and service industries, government, businesses and consumers to facilitate the production of British, European and International standards. This standard is a hEN. Again there may be more recent versions of the document. Intended to assist anyone involved in the design, specification and 771-3 of aggregate concrete blocks to understand the changes made in the latest standard and thereby continue to make the specification and procurement of aggregate concrete blocks as straightforward as possible.
Aggregate concrete masonry units dense and light-weight aggregates.
This is an important distinction between the previous custom of specifying and ordering blocks based on dimensions in the order of length bss height x width thickness. Tolerance D4 is intended solely for blocks to be laid with thin joint mortar, a technique rarely used in the UK. Supersedes BS EN This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3.
BS EN 771-3:2003
Requirements and test methods BS Search all products by. There is no doubt that over a period of 24 years BS has served our industry well in 7713- concise and unambiguous specifications for aggregate concrete bricks and blocks used in far ranging applications. Specification for masonry units.
Performance testing, Bricks, Dimensional measurement, Conformity, Acoustic absorption, Thermal resistance, Quality control, Density, Lightweight aggregates, Sound insulation, Cladding buildingsHeavyweight aggregates, Walls, Strength of materials, Masonry work, Thermal insulation, Concretes, Construction materials, Aggregates, Brickwork, Fire safety, Blocks buildingConstruction systems parts, Marking, Construction engineering works, Performance, Dimensional tolerances.
Want access to British Standards? Find Similar Items This product falls into the following categories. The appropriate test method is BS EN The Red document status indicator indicates that the document is an old version The document has likely been withdrawn by the publisher, also the meta data presented here may be out of date as it is no longer being maintained by the editorial teams at NBS. Your basket is empty.
Background BS EN Aggregate concrete masonry units is written as a performance standard which means that all requirements are based on the finished product, rather than prescriptive standards which limit the materials that can be used in manufacture. Aggregate concrete masonry units Important guidance for specifiers and users on a new Standard for aggregate concrete blocks Introduction BS EN Documents Flashcards Grammar checker.
Click here to find out how to access this document.
Understanding BS EN Aggregate concrete masonry units
Production of Exposed Aggregate Concrete. Worldwide Standards We can source any standard from anywhere in the world. Like most British Standards it has been necessary to adapt BS to suit an enlarged market as well as to reflect up to date materials testing and regulatory requirements.
These can be used in common, facing or exposed masonry in load bearing or non load bearing building and civil engineering applications, they are suitable for all forms of walling, such as single leaf, external leaf to chimneys, cavity wall, partitions, retaining, and basement.
Please download Chrome or Firefox or view our browser tips. Document Status Indicators The Green document status indicator indicates that the document is: March Replaced By: Customers who bought this product also bought BS EN Aggregate concrete masonry units. BS EN also categorizes units according to void percentages as follows: