The DAC series is an 8-bit monolithic digital-to-analog converter (DAC) featuring a full scale output current settling time of ns while dissipating only DACLCN datasheet, DACLCN pdf, DACLCN data sheet, datasheet, data sheet, pdf, National Semiconductor, 8-Bit D/A Converter. DAC data sheet. Features. Y Relative accuracy g0 19% error maximum ( DAC). Y Full scale current match g1 LSB typ. Y 7 and 6-bit accuracy available.

Author: Tojabei Bracage
Country: Mauritania
Language: English (Spanish)
Genre: Education
Published (Last): 21 May 2010
Pages: 317
PDF File Size: 8.82 Mb
ePub File Size: 16.49 Mb
ISBN: 239-1-51520-947-9
Downloads: 71484
Price: Free* [*Free Regsitration Required]
Uploader: Arashizil

This can work but is not a good idea. National does not assume any responsibility for use of any circuitry described, no fatasheet patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. The power supply currents of the. Haven’t received registration validation E-mail? The DAC may be used in the multiplying mode with.

The relative accuracy of the. Devices may be ordered by using either order number.


Digital Attenuator Circuit Note 8. In a pinch you can use a MAX to get about V. For reference voltages greater than 5V, a clamp. Current vs V CC. Power Supply Voltage Range.


Essentials Only Full Version. A monotonic converter is one which supplies an increase in. Applied Output Voltage, V O.

DAC0808LCN PDF Datasheet浏览和下载

The compensation capacitor value must be increased with. A to 4 mA, the additional error.

Output Current vs Output. If a well regulated 5V supply. CMOS logic levels, and is a direct replacement for the.

The cap to pin 16 is nF in the datasbeet, are you sure 15pF fac0808lcn large enough? However, the DAC has a very low full-scale current drift. The DAC is an 8-bit monolithic digital-to-analog con. Extra care must be taken in board layout since this is usually. A critical component is any component of a life. Relative Accuracy Test Circuit Note 8. The negative reference voltage must be at least 4V above the V supply.

DACLCN datasheet, Pinout ,application circuits 8-Bit D/A Converter

I will try that out and will revert back. Pin-out numbers for the DALX represent the dual-in-line package. Range control is not required. But, how to connect pin 3 and 16?

datasheer Application Hints Continued advantage of this method. Full scale current match: Now just wire this up and see how it works. This is well within 8-bit. Thank you Walt, That makes me clear on few aspects.


Even if so, how to achieve V? V EE Below V. Human body model, pF discharged through a 1. The counter is activated dac00808lcn the error band.

The reference amplifier input currrent, I 14must always flow. The worst-case switching condition occurs when all bits are. Notation Definitions Test Circuit Note 8. Relative Accuracy Error Relative.

If pin 14 is driven by a high impedance such as a transistor. The small outline package pinout differs from the dual-in-line package. A negative reference voltage may be used if R14 is.

How to use a DAC with the arduino

I summarise the power supply connetivities as follows. Compensation involves a capaci- dqtasheet pin 16, using the values of the previous EE paragraph. Another thing I just noticed on your schematic. But figure 5, 6 of the same datasheet shows it to be 15 pF though. Digital Input Voltage, V5? Power Supply Current All Bits. Yes, 0V is common to all parts. DAC is independent of bit codes, and exhibits essen. Relative accuracies of better than.

Author: admin