2N Low Power Bipolar Transistors. Page 1. 07/04/06 V Features: . Disclaimer This data sheet and its contents (the “Information”) belong to the. 2N Datasheet, 2N PNP Switching Transistor Datasheet, buy 2N Transistor. 2N Transistor Datasheet pdf, 2N Equivalent. Parameters and Characteristics.

Author: Gardashicage Arashir
Country: Guadeloupe
Language: English (Spanish)
Genre: Video
Published (Last): 16 November 2011
Pages: 227
PDF File Size: 7.58 Mb
ePub File Size: 18.51 Mb
ISBN: 944-7-18535-329-4
Downloads: 84598
Price: Free* [*Free Regsitration Required]
Uploader: Voodoojas

To make this current flow through the transistor the value of base current I B can be calculated using the below formula:. Overall it is just another small signal transistor which is commonly used in switching and amplifying circuits.

In datasgeet case for a collector current of mA we have to pass a base current of 16mA. To see a list of open positions, click here.

Facilities Lab Research in the department is conducted in a datashet of laboratories equipped with state-of-the-art equipment, with research funding coming from federal, state, and private sources. The value of this current can be calculated by the required amount of current that will be consumed by the load.

2N2905 2N2907

So if you looking for an NPN transistor that could switch loads or for decent amplification then 2N might the right choice for your project. Submitted by admin on 21 June Another important thing to keep in mind, while using datashfet transistor as switch is the base resistor. When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. Our People Search the directory for faculty or staff members.

PNP, Met, 60V mA, GP Amp & Sw – 2N

Current flows in through collector, normally connected to load. The 2N is a NPN transistor and is normally used as a switch in many circuits.


Where Vcc is the voltage on which the load operates and V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could adtasheet around mV. Engineering Program is accredited by: To make this current flow through the transistor the value of base current I B can be calculated using the below formula: However this vale will datsaheet be very accurate because the transistor will have an internal voltage drop across the collector current, so it mostly experimental to get the maximum current from the transistor.

Open Positions To see a list of open positions, click here.

TL — Programmable Reference Voltage. Here lets us assume the load here consumes around mA maximum so our collector current I C mA. Since transistor is of NPN the 2n29005 to be switched should be connected to the collector and the emitter should be connected to the ground as show in the figure below. Prices are subject to change without notice.

Spring Semester, Monday — Friday: But this calculation will lead to the closest value to start with. To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA by using a transistor to the base pin.

So to calculate the resistor value of the base we can use the formulae. The ECE Store provides many services to electrical and computer engineering students in order to create a safe environment in which students have access to the equipment and parts they need.


2N Datasheet(PDF) – Micro Electronics

Soldering Tips Helpful Link: This stage is called Saturation Region. This resistor is connected to the base pin of the transistor to datasheet the current flowing through the 22905. Complete Technical Details can be found at the datasheet given at the end of this page.

Where h FE, is the current gain of the transistor which in our case is In addition to supporting the various labs in the EL building, we also provide equipment and manual check-out and a wide range of electronic components for sale. So the value if R B will be. Welcome to the ECE Datasheet. Amplifier modules like Audio amplifiers, signal Amplifier etc. Current Drains out through emitter, normally connected to ground. As 2n29905 know the transistor is a current controlled device meaning, we have pass some current I B thorough the base of the transistor to turn it on.

The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. Search the directory for faculty or staff members.

But it comes in a metal can package and can operate on voltages slightly higher than what a 2N can handle. You can also see open positions in the department.

For details on these services, please click the appropriate link from the menu on the left.

Author: admin