DIN 50324 PDF

Standard [WITHDRAWN] DIN Tribology; testing of friction and wear model test for sliding friction of solids (ball-on-disc system). Buy DIN TRIBOLOGY; TESTING OF FRICTION AND WEAR MODEL TEST FOR SLIDING FRICTION OF SOLIDS (BALL ON DISC SYSTEM) from. Find the most up-to-date version of DIN at Engineering

Author: Mekazahn Tem
Country: Poland
Language: English (Spanish)
Genre: Career
Published (Last): 11 January 2008
Pages: 340
PDF File Size: 20.6 Mb
ePub File Size: 11.88 Mb
ISBN: 404-8-66404-245-8
Downloads: 17293
Price: Free* [*Free Regsitration Required]
Uploader: Nibei

Tapping Torque, Twist Compression, Drilling Tapping torque module allows to characterize friction, wear, torque etc. The test involves rotating one ball on three stationary balls at controlled environmental conditions. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but dim not provided as part of the standard.

Test involves slowly rotating a ring on top of material of choice. Stribeck Curve Stribeck curve is a plot between coefficient of friction and bearing number.

This test helps evaluate friction and wear parameters of piston ring liner material in presence of engine oils. The standard Test to determine extreme pressure, friction wear properties of lubricant greases, solid bonded films, gear and hydraulic fluids, lubricating oils.

High-load and high-temperature tribometer

Stribeck curve is a plot between coefficient of friction and bearing fin. Real time down force controlpiezo sensors to measure inline friction makes this module very reliable and repeatable. It is the responsibility of cin user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  GPG4WIN FOR ADVANCED USERS PDF

The coefficient of friction may also be determined. The test setup allows to mount real pieces of actual piston ring and liners.

Since the pin-on-disk test method does not attempt to duplicate all the conditions that may be experienced in service for example; lubrication, load, pressure, contact geometry, removal of wear debris, and presence of corrosive environmentthere is no insurance that the test will predict the wear rate of a given material under conditions differing from those in the test. The principal areas of experimental attention in using this type of apparatus to measure wear are described.

Thank you for your interest and filling out the form! Fast Exchange makes all these modules easily swapable on the MFT platform. Piston Ring Liner This test helps evaluate friction and wear parameters of piston ring liner material in presence of engine oils.

Loads from mN to 10,N.

Linear Oscillating The standard Test to determine extreme pressure, friction wear properties of lubricant greases, solid bonded films, gear and hydraulic fluids, lubricating oils.

In all modules listed above 5034 can change the load and velocity to automatically plot Stribeck Curves with ease. Twist Dun is designed to measure friction and adhesion in metal forming.

Materials are tested in pairs under nominally non-abrasive conditions. The value of any wear test method lies in predicting the relative ranking of material combinations. Contact us for a live Demo or additional information.

  DION FORSTER FILETYPE PDF

In this latter case, the results cannot be compared to the ILS data Table 2. Temperature and recirculation addons are also available. The ball is caused to rub against the disk 1mm stroke at a frequency of 50 Hz for vin min. The tests can be done in controlled environmental conditions including humidity, temperature and more.

No other units of measurement are included in this standard. Such a use of this standard is encouraged as a means to improve wear testing methodology. All tests are done in oscillation mode under controlled environmental conditions. Link to Active This link will always route to the current Active version of the standard. 503244

ASTM G99 – 17 Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus

Historical Version s – view previous versions of standard. However, it must be clearly stated in any report that, while 500324 directions and protocol in Test Method G99 were followed if truethe choices of test parameters were different from Test Method G99 values, and the test results were therefore also different from the Test Method G99 results. Work Item s – proposed revisions of this standard.

Author: admin