ECE R26 PDF

Regulation No 26 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of vehicles with. ECE R26 Regulation (03 Series, ) “The uniform regulations on vehicle chapter and section numbering betw een this standard and the ECE R ECE UNIFORM PROVISIONS CONCERNING THE APPROVAL OF: VEHICLES WITH REGARD TO THEIR EXTERNAL PROJECTIONS Incorporating.

Author: Tosho Daikree
Country: Grenada
Language: English (Spanish)
Genre: Finance
Published (Last): 26 November 2016
Pages: 444
PDF File Size: 12.6 Mb
ePub File Size: 6.46 Mb
ISBN: 991-5-17905-560-9
Downloads: 89089
Price: Free* [*Free Regsitration Required]
Uploader: Samujar

EUR-Lex – X(08)R(01) – EN – EUR-Lex

If the type of separate technical unit submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. An approved wheel shall not reduce the brake efficiency in comparison with a manufacturer’s replacement wheel. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation the symbol prescribed in paragraph 4.

Uniform provisions concerning the approval of vehicles of category L with regard to specific requirements for the electric power train This regulation submitted as document WP.

UN R10 Electromagnetic Compatibility. Application for type approval with regard to luggage racks, ski racks or radio receiving or transmitting aerials considered to be separate technical units shall be submitted by the vehicle manufacturer or the manufacturer of the aforementioned separate technical units, or by their duly accredited representative.

Drawings of the necessary sections through the external surface shall be provided by the manufacturer to allow the height of the projections referred to above to be measured. The regulation applies solely to “fixed-position flashing light devices whose flashing is obtained by the intermittent supply of electric current to the lamp”. A vehicle representative of the type of vehicle to be approved shall be ecee to the technical service responsible for conducting the approval tests.

  EJERCICIOS RESUELTOS DE MOLARIDAD PDF

They differ from vehicle manufacturer’s replacement wheels only by the absence of vehicle manufacturer’s trademarks and part number; 2. Uniform provisions concerning the approval of power-driven vehicle’s sealed-beam headlamps SB emitting a European asymmetrical passing g26 or a driving beam or both.

We use cookies to enhance site functionality and personalisation. In the case where negative results are recorded during one of these visits, the Type Approval Authority shall ensure that all necessary steps are taken to re-establish the conformity of production as rapidly as possible.

UN R8 Halogen Headlamps. Application for type approval with regard to luggage racks, ski racks or radio receiving or transmitting aerials considered to be separate technical units.

Translation of “Regulation ECE-R26” in Spanish

One for each impact position. The Type Approval Authority which has fce type approval may at any time verify the conformity control methods applicable to each production unit. UN Regulations provide uniform requirements for the approval of motor vehicles and equipment.

Wheel calliper check The design of the inner contour of the wheel wheel calliper ec Figure 1 must provide sufficient space for the brake, suspension and steering components. In the case where negative results are recorded during one of these visits, the competent authority shall ensure that all necessary steps are taken to re-establish the conformity of production as rapidly as possible.

Notice of approval, or of extension or refusal or withdrawal of approval or production definitively discontinued, of a type of separate technical unit pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation by means of a communication form conforming to the model in Annex 4 to this Regulation.

  ALGEBRA RECREATIVA YAKOV PERELMAN PDF

A fully searchable, accurate, user-friendly resource for consolidated regulations that are updated quickly and frequently. UN R16 Safety belt systems. Uniform provisions concerning the approval of vehicles with regard to their tyre pressure monitoring systems Program to separate tyre-pressure monitoring systems provisions from UN Regulation No. Dependent upon the particular vehicle the floor line trace may occur at the bumper section extremity or at the body panel below the bumper.

OJ L 70, 9.

Help Print this page. Fractures and indentations caused by the direct contact with the falling weight are acceptable.

Certificates and licenses

SCOPE This annex specifies a laboratory test procedure to evaluate the axial lateral r2 impact collision properties of a wheel manufactured either wholly or partly of light alloys. The hardness measurement shall be taken with the component as installed on the vehicle.

Technical service conducting approval test: R83 also contains provisions specific to hybrid variations of the vehicles under its purview. Furthermore, aerials shall be so fitted to the vehicle, and if necessary their unattached ends so restricted, that sce part of the aerials protrude beyond the extreme outer edge of the vehicle as defined in paragraph 2. UN R Retrofit Emissions. In the case where the calliper is inside the vehicle manufacturer’s replacement wheel calliper, a check shall be carried out of wheel operating clearance with respect to brake, suspension and steering components and general under body components, taking into account the effect of wheel balance weights.

Model B See Paragraph 4.

Author: admin