I would like to get a very nice trigger job on a SS GP for the single Ruger forum I found the IBOK for the GP on Google (GP IBOK). I received the GP pdf this morning. I found the IBOK so helpful thought I should bump it back up so others could keep seeing it. Gp Ibok – PDF Free. Download – -. Ruger sp manual pdf ruger sp manual pdf magnum revolver like the. Ruger GP For many.

Author: Aratilar Arashizil
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Business
Published (Last): 11 April 2008
Pages: 466
PDF File Size: 19.86 Mb
ePub File Size: 9.87 Mb
ISBN: 606-1-12867-945-2
Downloads: 87446
Price: Free* [*Free Regsitration Required]
Uploader: Meztirg

Use the windage screw to center the sight blade by turning the screw clockwise.

Transformed my GP today [Archive] –

Do the same test in DA by pulling the trigger and watching the cylinder latch. If the bore is damaged, the gun must be returned to the factory for a barrel replacement. Badger grips appear to change the grip angle but I’m sure it would be comfortable. All the options you have as far as making and shooting different iobk and powder charges without having to think about a malfunction is what makes me like them so much.

Gp10 is offering free shippping, so factor that into the price and I think it’s a pretty good deal.

After cleaning, insert the spring then insert the plunger with the slot up. He is a master gunsmith and specializes in Rugers.


A pawl that is too long causes premature carry-up. It too must be very smooth. Paranoia strikes deep, into your life it will creep. I have researched revolvers to buy for my hunting uses- I was going with a Smith model but now have purchased a GP, instead.

The notched end of the strut seat goes down with the flat surface to the front. I’ve previously done this work to my SP which went from being a so-so gun to my favorite of them all and to a SP This entry was posted on August 24, at 5: As for ammo, they’re bore sighted with gr at the factory, so that tends to be the best shooter. Set the rest of the gun aside for now. You may find a used one from Numrich or E-bay. Transfer bar is pulled down.

Push the sight plunger in while holding the sight down until the sight drops in place.

GP100 IBOK for SP101

Put a drop of gun oil on the shaft of the crane. Any suggestions are welcome. I assume ya I know is legal. Ibo a paper clip or wire as a follower and insert it into the trigger pivot pin hole. This makes trigger guard removal very difficult. SA sear releases the hammer.

GP IBOK for SP – Ruger Forum

This makes the spring and trigger link plunger part 47 drag and bind in both SA and DA. Instead of energy being efficiently transferred to the firing pin, much of the energy is wasted.


If it is too short, a new one will have to be fitted and installed at the Ruger factory. Thank you very, very much for posting this. The screw has thread lock. You can get it from Rugerforum.

Iowegan, I’ve also sent you an email requesting the. I called and the lady on the phone immediately emailed me a shipping label and return form.

Strange problem with my GP100

Thu Dec 06, Thank you so much! Look for chatter marks in the bore where the rifling is interrupted. Sounds like the beginning of a happy Ruger owner.

These edges and the ball tip need to be dressed down so the strut does not bind or drag on the mainspring or fulcrum seat in the hammer. Here’s a couple pictures of the gun after I finished; polishing the externals of the gun is not complete yet but here’s some pictures anyways: This little flipper transfers energy from the trigger to the hammer and brings yp100 to the cocked position.

Listen and feel for the feeler tip of the Range Rod to contact the cylinder face as you move the Range Rod in g;100 out.

Author: admin