HARDINGE BROTHERS, INC. ELMIRA check the part description to make certain the assembly and/or individual part applies to your machine. .. Bed. 2. Screw. 2. Washer. Front Screw. Lock Washer. 6. 14 D V. 0 0 1 0 2 1 4. D V B 0 0 0 9 7 7 6. 0 5 5 0 3 0 5. N 3 7 0 0 0 0 7 3 6. 5 p. 0 0 0 6 4 3. HARDINGE DV59 DSM59 Lathe Part Manual DV DSM [Misc.] on Amazon. com. *FREE* shipping on qualifying offers. Number of Pages: 15 This is a. DV59 Precision Lathe and DSM This is a reproduction, not a photocopy, of an original Hardinge DV59 Precision Lathe and DSM59 Second Operation.
|Published (Last):||5 February 2013|
|PDF File Size:||6.10 Mb|
|ePub File Size:||6.16 Mb|
|Price:||Free* [*Free Regsitration Required]|
Initially the setup will be tried for drilling, boring, turning and facing operations only, with the spindle running with the existing arrangement of induction motor drive. Will you be using MACH3? Roy, Here are a couple I found on eBay. This lathe Uses 5C collets. I do have the carriage blocks drawn up and tool paths for when they get machined. I may have more than one manual that covers your machine, and I am adding new manuals all the time.
Fully functional and working.
Also, as the screw heats up from continious running, it will expand, and possibly bind the ahrdinge at the ends. Which is the better way?
Thanks, RRossey Similar Threads: The existing Hardinge cross slide can be moved and fixed on the bed of lathe. Hardijge believe this manual will be a valuable resource of knowledge that will provide a lot of helpful information that is often hard to find. In the second view, the top table is removed. The above arrangement will give sufficient place on the longitudinal slide of the table to mount three or four tools and possibility of mounting a live tool also. This page was last updated: The turret dv-9 tight once indexed it does not have wobble.
It has the head stock that clamps to the bed not bolts to.
Intermediate shaft slides side to side. If you were to put one angular contact bearing at each end, it would be tough to remove the backlash. Take gearbox off if changing the top spindle belt 3. I am yardinge the email confirmation. So the preloading has to be done to get this particular position, probably by providing shim washers, by trial mmanual error. Hopefully its the early headstock.
I propose to complete this project in two phases Phase I I will keep the head and spindle of the DV 59 lathe as it is, driven by 1 HP induction motor. Swing Over the Bed: Note that these drawings have change numerous times so even these may not be the last, however for my first attempt at this conversion these should be it.
So for initial trials the tools will have to be mounted in special tool holders to match the spindle axis.
Hardinge Dv59 Dsm59 Lathe Part Manual Dv-59 Dsm-59 0334
I was creating the tool-paths today to drill and tap for the mounting of the THK rails and the bed to the lathe body, I was also hqrdinge surprised how inconsistent the spacing was on the 18 holes that originally secured the V-Way.
It uses an older MicroKinetics control system with steppers driving timing belts.
Ships on time with tracking, 0 problems with past sales. I built a small lathe using a precision x-y table and stepper motors that I use every day.
The time now is Board index All times are UTC. What is the torque of stepper motors? The included tool holder is from a Hand Chucker cut-off slide. To learn and have the basic insight of CNC Project: I received the cross slide table.
Shaft will go far enough to right for the shaft to come out of bearing 6. I would be most appreciative if someone could help out.
The spindle axis is at 4. Marty, They have a manual here. Run speed adjustment to top 2. Approx 60″ Long x 48″ Wide x 59″ High.
I do not carry additional parts for machinery, except for what is listed. It is in very good condition. I may later make the truck pads to the top carriage plate a one piece unit.
Remove both ev-59 lead screws and replace with rolled ball screws and two nuts on each screw. I still haven’t figured out.
Hardinge Dv59 Later Model Metal Lathe Operator’s Manual | eBay
This is because of possible changes in rates of thermal expansion. Again the shims and spacers are to be provided to eliminate back-lash. These do not come out easily on the handwheel side of the head like the newer model.