INTERPLATER HD85 135 THERMAL PDF

Interplater hd85 thermal pdf. Thermal analysis and design enae d principles of space systems design u n i v e r s i t y o f maryland nonideal radiative. Service Manual + 68/85 Plate Processor InterPlater 85/ HD Polymer Service manual Plate Processor+ 68/85 .. Cleaning of developer heating element. Thermal Plate Processor Raptor 85/ Interplater HD 85 G&J used/refurbished. Glunz Jensen Interplater Plate Processor Model Perfect Condition.

Author: Gagar Kiganris
Country: Jamaica
Language: English (Spanish)
Genre: Software
Published (Last): 16 June 2014
Pages: 40
PDF File Size: 11.23 Mb
ePub File Size: 19.70 Mb
ISBN: 123-4-62173-813-3
Downloads: 35693
Price: Free* [*Free Regsitration Required]
Uploader: Daijora

As shown in the figure below the hose must be connected between the water tap and the water inlet solenoid valve located to the left, when standing in front of the processor, underneath the processor.

The recommended minimum free space around the machine is specified in the illustration below.

Mount the supports through the holes interplatr the exit table 2turn them to lock them inside the holes. F17 Transport motor M1 4AT, 6.

Cable for connection to a stacker is placed underneath the dryer section. Normally no adjustments are necessary. Procedure of adjustment See illustration on the following page.

The parameters to be configured are: Repeat 2 and 3 for the gear end of the brush roller. The roller 5 makes sure of proper contact between brush and plate. Therefor plastic or rubber is recommended.

  CAFE ZUPAS MENU PDF

Processor must stop when the switch is deactivated.

Glunz Jensen

The rollers 7 at the section exit squeeze any residual water off the plate. Note the position of the outlet nozzle 5. Select NO otherwise the system will start replenishing based on how many hours the machine has been switch off since the machine has been packed. Recycling The processor should be disposed at a certified appliance recycling centre or processing centre.

InterPlater 85/135 HD Thermal

Before operating the processor you may need to perform a rewiring to match your local supply voltage. Press the upper roller into the bearing by pressing the roller key upwards 3.

To mount the handshower please follow the description below and the illustration opposite. See power outlet and fusing requirements later in this manual. This is done when installation of the processor has been completed. When changing a fuse, first switch off all power to the machine. Unpack the cable and connect it to the stacker see also the stacker manual.

Functional description General Processor sections The processor contains six major sections, each performing a basic function to change the exposed plate into a fully developed and dry plate, ready for handling see illustration below. If main power has been cut off temporarily the processor switches to off mode green led flashes. Set developer brush speed according to recommendations from the plate manufacturer.

  ANTHROPOLOGY AND ANTIHUMANISM IN IMPERIAL GERMANY PDF

End of life Estimated product life: X3,D to F10,1 Blue: Thermal energy can flow from one object to another by. Occasionally, depending on the local water quality, it may be necessary to use a drill bit to clean the holes and remove sediments mechanically.

Products | Glunz & Jensen

Also the developer top-up function automatically adds fresh developer to the developer section when low level is detected. The rollers 9 ensure that the plate is transported correctly underneath the brushes 10 and the rollers 11 make sure of proper contact between brushes and plate. Configuration and settings Additional configuration might be necessary to suit the individual customer needs. The pre-heat section rollers 1 transport the plate through the pre-heat section. Installation hours for off-line machine: Manuals are available from the manuals link to the right.

The MIO-board is equipped with a platesetter interface for communication between the processor and platesetter. The exit table is mounted from the factory and prepared for slanted position A. See the table on the following page for a description of the fuses.

Author: admin