IPMP CONFIGURATION IN SOLARIS 10 PDF

These topics include IPv4 and IPv6 network configuration, managing TCP/IP 1. Oracle Solaris TCP/IP Protocol Suite (Overview) The default is 10 seconds. Oracle Solaris Administration: IP Services Oracle Solaris 10 1/13 Information An IPMP configuration typically consists of two or more physical interfaces on the . For IPMP configuration tasks, refer to Chapter 31, Administering IPMP (Tasks). Oracle Solaris IPMP involves the following software: You can configure one of the interfaces down to 10 megabits and still place the two interfaces into the.

Author: Kigadal Nit
Country: Yemen
Language: English (Spanish)
Genre: Love
Published (Last): 8 October 2007
Pages: 24
PDF File Size: 19.39 Mb
ePub File Size: 4.37 Mb
ISBN: 753-8-54333-243-9
Downloads: 16095
Price: Free* [*Free Regsitration Required]
Uploader: Nilkis

During IPMP group configuration, in.

These messages are informational in nature and indicate that the IPMP configuration functions correctly. After failback, the original configuration is restored. Add IP interfaces to the group. The attachment of the interface to the IP link is down.

Solaris11 Self Paced Video Learning. Load spreading occurs only when the network traffic is flowing to multiple destinations that use multiple connections.

As a result of load spreading, higher throughput is i;mp. Routers that are connected to the IP link are automatically selected as targets for probing. Some NICs can have multiple physical interfaces. I have started unixadminschool.

You can use host routes to explicitly configure a list solqris target systems to be used by in.

Chapter 30 Introducing IPMP (Overview)

Consult your platform’s documentation for details. You do not need to mark an IPv6 test address as deprecated to prevent applications from using the test address. IPMP detects the following types of communication failures:.

  AMPROBE DGC-1000A PDF

You use IPMP options of the ifconfig command to create the configuration. The standard IPv4 and, if applicable, IPv6 packet traffic through an interface is considered to be data traffic. You should receive a status message regarding this event. IPMP detects the following types of communication failures: Make sure the NIC status are up and not in use.

An IP address associated with an deprecated interface will not be used as source address for outbound packets unless either there are no other addresses available on the interface or we respond to incoming requests for that IP address. An IPMP configuration typically consists of two or more physical interfaces on the same system that are attached to the same IP link.

For example, a qfe NIC can have four interfaces, qfe0 through qfe3and so on. You should configure only test addresses on a standby interface. Some Sun platforms might only support DR of certain types of hardware.

Check the IPv4 configuration for a specific interface. Additionally, any existing connections to the system using those IP addresses are disrupted. The recipient of these addresses is a functioning interface in the failed interface’s IPMP group.

After the daemon receives 10 consecutive replies for a default repair detection time of 20 seconds, the daemon determines that the interface is repaired.

All requests to detach system components that contain NICs are first checked to ensure that connectivity can be preserved. Link-local addresses are automatically configured configuratino the interface becomes IPv6-enabled at boot time or when the interface is manually configured through ifconfig.

  IRENE VASILACHIS ESTRATEGIAS DE INVESTIGACION CUALITATIVA PDF

Note ln the in. Internet Key Exchange Reference To enable probe-based failure detection, you need to assign a test address to the interface. Consider the example of four VLANs, bgebgebgeand bge The dummy address was created so that hme0 can still be accessed. IPMP also provides load spreading of packets for systems with multiple interfaces. See Detecting Physical Interface Repairs for more information.

IPMP Interface Configurations – Oracle Solaris Administration: IP Services

Awesome article and nicely explained. Verify the ifconfig output as well. Otherwise, the detach request completes successfully. IPMP does not permit you to add a data address to an interface that is configured through the ifconfig command as standby. After you have configured a test address, you need to ensure that this address is not used by applications.

You can observe this flag in the status lines for the interface in the ifconfig output.

In a dual-stack environment, placing the IPv4 instance of an interface under a particular group automatically places the IPv6 instance under the same group. DefaultFixed NCP is enabled; automatic network management is not available. Configuring IKE Tasks Place each physical interface into an IPMP solwris.

Author: admin