LA3600 DATASHEET PDF

LA datasheet, LA circuit, LA data sheet: SANYO – 5-Band Graphic Equalizer,alldatasheet, datasheet, Datasheet search site for Electronic. LA datasheet LA component LA integrated circuit LA schematic LA application note A LA LA36 LA3. Sanyo LA datasheet, 5-Band Graphic Equalizer (1-page), LA datasheet, LA pdf, LA datasheet pdf, LA pinouts.

Author: Zolotilar Shataur
Country: Reunion
Language: English (Spanish)
Genre: Health and Food
Published (Last): 21 April 2005
Pages: 322
PDF File Size: 16.3 Mb
ePub File Size: 18.36 Mb
ISBN: 892-4-45918-771-7
Downloads: 19650
Price: Free* [*Free Regsitration Required]
Uploader: Gum

Capacitor C13 is a decoupling capacitor and C14 is a power supply filter circuit.

Then the contour of the knobs represents the frequency response of the tone control unit. Assemble the circuit on a good quality PCB. Your email address will not be published. Capacitors C2, C4, C6, C8, La6300 and C15 are the input capacitors and increasing the value of these capacitors will increase the low frequency response.

Capacitors C2, C4, C6, C8, C10 and C15 are the input capacitors and increasing the value of these capacitors will increase the low frequency response. You may also like: The LA can be operated from anything between 5 to 15V DC and is extremely stable to capacitive loads.

datashewt

Gain of each band can be adjusted by using the corresponding potentiometers R1 to R5. Datashedt is the output capacitor and resistor R6 limits the supply current. The power supply must be well regulated and noise free.

  INTERTRIGO TRATAMIENTO PDF

(PDF) LA3600 Datasheet download

Hi Eric Nice question. Then the contour of the knobs represents the frequency response of the tone control unit.

I used 9V DC for powering the circuit. In the circuit capacitors C1, C3, C5, C7 and C9 are used to fix the resonance frequency of the corresponding bands.

(Datasheet) LA pdf – 5-Band Graphic Equalizer (1-page)

This will hold good only when following are carried out. If you use slider potentiometers as controls and mount them vertically in a sequence from left to right as R1 to R5 and as you slide it down, should cut the frequency spectrum for which it is meant and sliding up should boost.

Hi Eric Nice question.

Most l3a600 the IC manufacturers call their multi band tone controls as graphic equalisers. Leave a Reply Cancel reply Your email address will not be published. The LA can be operated from anything between 5 to 15V DC and is extremely stable to capacitive loads. Capacitor C13 is a decoupling capacitor and C14 is a power supply filter circuit. Could i add this to my homemade tube amp, and take out the LA?

C12 is the output capacitor and resistor R6 limits the supply current. In the circuit capacitors C1, C3, C5, C7 and C9 are used to fix the resonance frequency of the corresponding bands.

Leave a Reply Cancel reply Your email address will not be published. La36600 is a single integrated single Op-amp, 5 band graphic equalizer IC which is very suitable for applications like portable stereo, radio sets, home theater systems, car audio systems etc.

  ENFERMEDAD DE PERTHES EN NIOS PDF

LA Datasheet pdf – 5-Band Graphic Equalizer – SANYO

If you use slider potentiometers as controls and mount them vertically in a sequence from left to right as R1 to R5 and as you slide it down, should cut the frequency spectrum for which it is meant and sliding up should boost. Previous post Next post.

This will hold good only when following are darasheet out. The power supply must be well regulated and noise free. Assemble the circuit on a good quality PCB. Could i add this to my homemade tube amp, and take out the LA? Gain of each band can be adjusted by using the corresponding potentiometers R1 to R5.

Most of the IC manufacturers call their multi band tone controls as graphic equalisers. LA is a single integrated single Op-amp, 5 band graphic equalizer IC which is very suitable for applications like portable stereo, radio sets, home theater systems, car audio systems etc.

How we connect stereo input to this circuit? You may also like: How we connect stereo input to this circuit?

Your email address will not be published. I used 9V DC for powering the circuit. Previous post Next post.

Author: admin